Product - Description
Price Ex GST
Price Incl GST
Enduro Outboard BB Cup Tool
X-Type Bottom Bracket Outboard Cup Tool
Removes and installs bearing cups for outboard type bottom brackets like the Shimano Hollowtech II, Race Face X-Type, FSA, Truvativ.
Designed not to mark the cups or cause burring, these will keep your cups looking like new.
Uses a standard 1/2 inch socket drive. Includes crank arm cap tensioner for Hollowtech II systems. Replaces tools TL FC32 and TL FC16
Enduro BB Cup Tool - Campagnolo Ultra Torque
Campagnolo Ultra Torque Bottom Bracket Cup Tool
Designed to allow the removal and installation of Campagnolo Ultra Torque bottom bracket cups with marking them. Fit a standard 1/2 inch socket drivers allowing for correct torque.
Enduro Blind Hole Bearing Puller
Enduro Blind Hole Bearing Puller
Use to remove cartridge bearings from seats. Includes collets to remove bearings with inside diamter 8mm-32mm.
Can also be used to remove remaining outer race from disintegrated bearings.
Enduro Outboard bearing replacement tool
Bottom Bracket Outboard BEARING PULLER/PRESS
Removes and installs bearings in outboard type bottom brackets like the Shimano Hollowtech II, Race Face X-Type FSA, Truvativ.
Enduro Bearing Replacement Tool 30mm BB
For replacing bearings in BB30 and Cannondale SI type BB's
Bearing Puller for Campag UT crank bearings
Enduro Hub Bearing Press
the Enduro Hub Bearing Press is designed too allow the user to easily and safely press any combination of bearings into hubs. Bearing drivers are provided for;
Cannondale Crank Spider Lockring tool
Cap Pin Tool FSA Cannondale Zipp
This tool allows you to remove the cap pin on the FSA, Cannondale and Zipp Crank Sets
Bearing Puller for Campag Ultra Torque crank
Removes bearings from Campagnolo Ultra Torque bb crank arms
DIY MTB Shock Bushing Tool
Shock eye bushing tool for mountain bike rear shocks.
With the right drivers you can replace the standard bushings on most model shocks as well as Enduro Needle bearings for 1/2 inch shock eyes.
With a 6mm allen key you can replace shock eye bushings quickly. On many bikes you can change the bushing without removing the shock from the bike.
Includes: 1/2 inch bushing driver for Fox Rockshox newer X-Fusion etc. Other drivers are available see Shock eye bushing hardware and tools
DIY MTB Star nut puller cone
Make installing a star nut easier. Pretty simple bit of kit, ccmbined with some threaded rod allows you to pull the star nut into place.
DIY MTB Star nut puller set
Includes the cone, threaded rod nut and washer. All you need is a 10mm socket and ratchet or similar
Enduro Bearing Grease for Ceramics 10ml
Suitable for all bearings this is the grease used in our ceramic hybrids
This grease is light but stays in place and retains state without drying.
Suitable for all high precision ceramic and steel bearings
Enduro Bearing - Bearing V Puller Tool
Dimensions: 10-25 mm IDTypical Application:
Lefty Hub Tool
Allows easy removal installation and torquing of the Lefty Hub cap. This cap is required to be removed to replace the hub bearings.
Measuring Jug – 250ml
Squeeze bottle - 250ml
Shock Eye Bushing - wide 1/2 inch
Suit fox ALPS series
1/2 inch ID x 3/4 inch wide (12.7mm x 19mm)
Shock Eye Bushing - 12mm
aka DU Bushings. 12mm for Manitou, Rock Shox 05 on
Shock Eye Bushing - 1/2 inch
aka DU Bush In 1/2 inch for Fox, 5th Element coil, Romic etc